Competitor Search Guided Search
click here to chat with us
MDVF05-D230-PCM

MDVF05-D230-PCM

MDVF Series

The MDVF Series is the latest offering in a growing list of VFDs from Minarik Drives. Able to control 115 and 230 VAC, single and three phase motors, the MDVF Series is designed to meet the market demands of VFD users who wish to simply run their motors without the complicated menu-driven setup typical of most VFDs today.

The onboard microprocessor allows for custom programming for OEMs. Whether it’s as simple as changing the purpose of a jumper, input, or trim pot, to programming entire routines and behaviors specific only to the OEMs application, the MDVF is great for integrating PLC like functionality into your operation. Doing this can eliminate the need of a separate PLC altogether or enhance a system that currently does not have one.

The MDVF Series is certified to the new UL 61800-5-1 Standard, meaning not only does it contain isolation for remote control from an analog signal, but also has internal Motor Overload Protection circuitry. If a motor requests more amperage than the motor overload protection setting, the drive begins an internal countdown until faulting out. The higher the overload condition, the faster the countdown. With motor overload protection built into the MDVF Series, users won’t have to install expensive external devices the perform this function to meet future UL requirements.


Potentiometer Kit 202-0177 is included with a purchase of the MDVF05-D230-PCM

$406.00
Model
Number
Enclosure Maximum
Current
(ADC)
Input
Voltage
(VAC)
Input
Frequency
(Hz)
Output
Voltage
(VDC)
Output
Frequency
(Hz)
Power Range Braking Reversing Isolation
HP kW
MDVF05-D230-PCM Chassis 5* 115 / 230 50 or 60 Hz 0 - 115 50 or 60 Hz 1/16 - 3/4 .05 - .56 Yes
(DC Injection)
Yes 0 ± 5 VDC
0 ± 10 VDC
4-20 mA
0 - 230 50 or 60 Hz 1/8 - 1 1/2 .09 - 1.1

* When mounted to allow upwards airflow through the heat sink fins. De-rate to 4.0 amps when mounted in any other configuration.

Features

  • UL 61800-5-1 Listed: Tested to the new UL standard to be implemented in 2020.
  • Microprocessor based: Allows custom programming for OEM’s.
  • Control a variety of motors: 3-phase induction motors, single-phase permanent split capacitor (PSC), shaded pole, and synchronous motors.
  • Doubler mode: Can double a 115 VAC line to run a 230 VAC motor.
  • Isolated inputs: Accepts floating or grounded signals 0 ± 5 VDC, 0 ± 10 VDC or 4-20 mA.
  • Diagnostic LED: LEDs for power and status (undervoltage, overvoltage, short circuit/current trip, overheating warning/trip).
  • Thermally protects: Drive recognizes when overheated as a result of overload. It first flashes a warning code on the status LED and will eventually trip if the condition persists.
  • Stopping modes: User can use DC Injection braking, decelerate, or coast the motor to a stop.
  • Dump circuitry: Internal circuitry for the hookup of an external dump resistor.
  • Quadrature encoder option: For OEM applications, the drive can be programmed to follow quadrature encoder feedback without any circuitry changes.

Trim Pots

  • Minimum Speed
  • Maximum Speed
  • Acceleration
  • Deceleration
  • Torque
  • Voltage Boost
  • Slip Compensation
  • Brake Current
  • Brake Time-Out